TeslaElon's post · 17 NovMUSK AND ENGINEER MARKED SPOT WELDS TO CUT

Tesla Spot Weld Cuts: Musk and a Structural Engineer's Picks Matched

Elon Musk says he and one of Tesla's best structural engineers each marked spot welds to delete on one side of a symmetric body, and their calls lined up apart from a few that were quickly settled.

Illustration of a symmetric bare car body with small blue points marked along its seams
Musk says he and a structural engineer each marked spot welds for deletion on one side of a symmetric body. Illustration: ENNIllustration
AT A GLANCE
Elon's post · 17 Nov

Musk's own post shows what he says happened; it does not name the vehicle or give weld counts, and no outside source has confirmed the details.

What happened
Musk and one of Tesla's best structural engineers each marked spot welds for deletion on one side of a symmetric body-in-white
The result
Their judgments matched exactly, apart from debate about a few, settled quickly
The stakes
Musk says a wrong call would have resulted in a recall
Vehicle
Not named in the post
Date
17 November 2026
STORY THREAD Elon Musk on Tesla manufacturingFirst report in this thread. Updates will appear here.

Elon Musk has given fans a rare look at how he works on the Tesla production line, right down to individual spot welds. In a post on 17 November, he says he had one of Tesla’s best structural engineers mark spot welds for deletion on one side of a body-in-white, while he marked the other side himself.1 Their judgments, he says, matched exactly, apart from debate about a few, which was settled quickly.1

It is a short post with a big idea inside it: the CEO of one of the world’s most valuable companies is personally deciding which welds a car body can live without, and his calls line up with a specialist’s.

What Musk posted

The setup is simple. The welds on the body are symmetric, Musk explains, so the engineer took one side and he took the other.1 That made the two sets of marks directly comparable: wherever one of them flagged a weld on the left, the matching weld on the right would show whether the other had reached the same conclusion.

Musk’s answer is that they did, apart from a handful of welds that were debated and quickly resolved.1 Then he states what was on the line. If they had been wrong, he writes, it would have resulted in a recall.1 His closing line is three words long.

If we had been wrong, it would have resulted in a recall. We were not.

Here is the full post:

What the post does and does not say

Musk refers to “the body-in-white” but does not name the vehicle it belongs to.1 He also does not give the number of welds marked, how many were removed, which engineer he worked with, or when the exercise took place.1 ENN is reporting exactly what he wrote and is not filling in those gaps.

What the post does make clear is the order of events as he describes it: the welds were marked, the few points of disagreement were debated and settled, and the result held up without the recall he says a mistake would have caused.1

Tesla's Gigafactory Texas building
Giga Texas, where the first production Cybercab rolled off the line in February 2026.Illustration

Why deleting parts matters at Tesla

Taking things out of a car is a recurring theme in Tesla’s recent manufacturing story, and the Cybercab is the clearest example. The first production Cybercab rolled off the line at Gigafactory Texas on 17 February 2026, according to a Markman Capital Insight analysis.2 It has no steering wheel, no pedals and no side mirrors, and it has roughly half the part count of a Model 3.2

The same analysis describes Tesla’s “Unboxed” process, in which five to six major modules are built in parallel, including the front end, the structural battery pack with interior, the rear end and the left and right side structures, before robots join them in a final step.2 Tesla’s Q1 2026 earnings call claimed the method cuts factory footprint by 40% and labor costs by 30% compared with traditional linear assembly, the analysis reports.2 Tesla’s internal goal at full scale is one Cybercab every 10 seconds.2

The boldest deletion was the paint shop itself. The Cybercab uses polyurethane body panels with the color molded in, and plastic parts are welded ultrasonically.2 Tesla’s vice president of engineering, Lars Moravy, said the company took the idea of deleting the paint shop from the Cybertruck and carried it forward.2

We only really coat things that need corrosion protection at this point.

That quote from Moravy appears in the Markman piece.2 Spot welds are a much smaller unit than a paint shop, but the logic Musk describes is the same: each item that can safely come out is one less thing to build.

A long-running Musk habit

Commentators have pointed to this cost-first thinking for years. When the Cybertruck was unveiled in 2019, X user Brad Garcia argued in a widely shared thread that the truck’s design was “entirely driven by cost” and that Musk is “a huge fan of going back to first principals.”3 Garcia highlighted two deletions in particular: the truck dropped pressed body panels, which he called the most expensive machines in the production process, and it dropped paint, with stainless steel addressing the oxidation problem.3

The same material-and-process focus shows up at SpaceX. In 2024, investor Eugene Ng summarized a Musk explanation of why Starship uses a stainless steel alloy rather than carbon fiber or aluminum: it is heavier, but much cheaper at $4+/kg instead of $150/kg, easy to weld and repair, and does not need paint.4 Musk himself posted the clip for anyone who wanted “a detailed explanation of why I switched Starship from carbon fiber to stainless steel.”4

Today’s post fits that pattern from a new angle. Rather than an executive setting a broad goal, it shows Musk at the level of individual joints in a body structure, making calls that he says matched those of a structural specialist.1

Illustration of robot arms welding a car body section in a dark factory
Every spot weld removed is one less step on the line. Illustration: ENNIllustration

The bigger picture for Tesla

Manufacturing efficiency carries real weight for Tesla’s investors. Tesla was valued at around 1.48 trillion dollars as of late October, according to Vontobel Markets, citing Finanz und Wirtschaft.5 Vontobel also notes that Tesla and SpaceX are exploring a potential merger, with committees formed at the request of shareholders, and that Musk personally considers a merger a good idea while declining to call it certain.5

The Markman analysis argues that the manufacturing side may matter even more than any single car: with half the parts, no paint shop, parallel module assembly and ten-second cycle times, it says, the cost per vehicle collapses.2 It also records a cautious view from Morgan Stanley’s Adam Jonas, who, while generally bullish on Tesla, has said the path to a profitable robotaxi network is longer and more uncertain than Musk’s public statements suggest.2 That debate is about the robotaxi business rather than welding, but it shows why investors watch every production efficiency Tesla finds.

ENN does not offer investment advice, and the post itself contains no figures on savings.1

What to watch next

The open questions are the ones the post leaves unanswered: which vehicle’s body-in-white this was, how many spot welds were removed, and what the change means for build time or cost.1 If Musk or Tesla follow up with those details, ENN will add them to this thread.

For now, the takeaway is the one Musk chose to share. A demanding engineering call was split down the middle of a symmetric body, two people made their marks, and the answers came out matching, with only a few welds needing discussion.1 Musk says a wrong call would have meant a recall. In his words: “We were not.”1

Questions readers ask

What did Elon Musk say about spot welds?

He said he had one of Tesla's best structural engineers mark spot welds for deletion on one side of a body-in-white while he did the other side, and their judgments matched exactly, apart from debate about a few that was settled quickly.

Which Tesla vehicle was it?

The post does not say. ENN is not naming a vehicle until Musk or Tesla does.

Why does he mention a recall?

Musk wrote that if they had been wrong, it would have resulted in a recall. He added: "We were not."

Why could the two sides be compared?

Musk says the welds are symmetric, so each person marked one mirror-image side of the same body.

Sources

Each story is checked against the original material and independent reporting. Numbers in the text point here.

  1. 1
    PrimaryPost on marking spot welds for deletion X (@elonmusk) · Nov 17, 2026
  2. 2
    CoverageTesla's "Part Deux" Vision Enters Production Markman Capital Insight · Apr 16, 2026
  3. 3
    ReferenceThread on the Cybertruck's cost-driven design X (@bradgarcia) · Nov 23, 2019
  4. 4
  5. 5
    CoverageTesla and SpaceX: Merger Takes Center Stage Vontobel Markets · Nov 2, 2026